XCore Exchange

Hello !!
The problem-related to the SD card read/write as per this library suggestion.
https://github.com/xcore/sc_sdcard

Mode for communication which I selected SDCardHostSPI.
I am using xCORE-200 Explorer Kit for this operation. Connection wire as per mentioned in SDCardHostSPI.xc file.
Also, I placed pull up resistor on the MISO pin. It is necessary or not which I am not sure.

MMC card adapter using for the place my SD CARD model number SanDisk Ultra 32GB Class 10.
Also, I resolved all the warning(not necessary) Still I did it.

When I run this program I got the error like,

Failed with rc=3.

I hope any one help to resolve my problem. Thank you.

Hi. Received your private message.

1) post your full project and full output log from execution.

2) post your wiring diagram. What is the power rail for this sd-card?

3) post a picture of your sd-card

See limited but working reports in the forum for this topic.

Is the sd card formatted? To which format?

Hi. The project and code is not supported by XMOS due to the age of the post but see if the attached document helps. I think you have assorted options including the use of a low cost external spi bus sd-card reader, etc. you could mate with the XMOS CPU.

I think the best way to approach this is..

1) confirm you can replicate the results in the posted document

2) consider to source the low cost arduino and sd-card hardware setup shown here:

https://create.arduino.cc/projecthub/el ... ata-37f390

3) confirm that the arduino setup works for you. Then tweak the XMOS code to do the same.

4) a low cost spi bus sniffer from eBay , Amazon, etc. will be helpful here to confirm you can send and receive over the spi bus.

Onces again thanks for reply me.
I am using stable version of 1.0.1 and my connection should be liked,

// Structure for the ports to access the SD Card
C M S M
s o c I
s l s
i k o
__________________
/ | | | | | | | | |
|| C D - + C - D |
| S I G 3 L G O |
| N . K N |
| D 3 D |
| V |
*/
static SDHostInterface SDif[] = /* LIST HERE THE PORTS USED FOR THE INTERFACES
cs, sclk, Mosi, miso */
{{XS1_CLKBLK_1, XS1_CLKBLK_2, XS1_PORT_1L, XS1_PORT_1I, XS1_PORT_1K, XS1_PORT_1J, 0, 0}}; // resources used for interface #0

So, I directly connect sd card to xmos pins no other hardware I am using for interface. Even I checked my sd card in arduino for interfacing.
Also, I am using the 14.0.1 xmos software for build this program.
As per pdf, XMOS SDCARD library - Version 1.3.0 required if possible then share my folder because I tried to find but I couldn't get it.
I hope you really help me.
Thank you.

Zip up your full project and post here for a review.

If you wish, you can use a cloud service like wetransfer and then post the url.

Post your makefile.

What is the value of SD_SPI_ENABLE?

It should be SD_SPI_ENABLE=1 in the makefile so that SPI mode (1 bit ports) is selected.

Also...from the github source code:
So rc=3 means, Not Ready.

Check your wiring. Check your voltage to the sd card.

Do you have a multimeter or scope or logic analyzer tool?

Use them to confirm that your spi port pins are actually working when you run this code.

SD card? Are not all mobile hard drives now? I haven't used the SD card for a long time, and there is no portable hard drive.

As per this link, I tried to get data through SD card still I do not get it.

https://tuck1s.blogspot.com/2015/08/xmo ... to-sd.html

My memory card should be this one,
I am using Sandisk Adapter,
Pin1 (CS ) ----> P1L
Pin2 (MOSI[DI]) ---> P1K
Pin3 (GND) ---> GND
Pin4 (3V) ---> 3V3
Pin5 (CLK) ---> P1I
Pin6 (GND) ---> GND
Pin7 (MISO[DO]) ---> P1J
Pin8 (NC) --->NC
Pin9 (NC) --->NC

I tried to place 10k pull up on pin2[MOSI] and pin7[MISO]. Still do not get any response.

I tested the same thing Arduino sd card module it works well.

In SDCardHostSPI.xc,

static SDHostInterface SDif[] = // LIST HERE THE PORTS USED FOR THE INTERFACES
// cs, sclk, Mosi, miso
{{XS1_CLKBLK_1, XS1_CLKBLK_2, XS1_PORT_1L, XS1_PORT_1I, XS1_PORT_1K, XS1_PORT_1J, 0, 0}}; // resources used for interface #0

changed as per defined output.

I hope anyone help me getting out this problem.

here the link for my code.

https://we.tl/t-18MXkYfgEo